Wachsmuth Krogmann Iron ES 139B User Manual

STEAM IRON  
MODEL ES-139B  
ITEM# 1996-05  
PLEASE READ THESE AND SAVE ALL INSTRUCTIONS TO ENSURE THE  
SAFE AND EFFECTIVE USE OF THIS APPLIANCE.  
 
IMPORTANT SAFETY INSTRUCTIONS  
INTRODUCTION  
Thank you for purchasing our Crofton Steam Iron. Each iron has been manufactured to  
ensure safety and reliability. Before using for the first time, please read the instructions  
carefully, and keep them for further reference.  
WARNING! READ AND SAVE THESE INSTRUCTIONS. Failure to follow all  
the instructions listed below may result in electric shock, fire and/or serious personal  
injury.  
IMPORTANT SAFEGUARDS  
Please read these instructions in conjunction with the illustrations before using the  
appliance.  
Before using for the first time, check if the voltage rating on the rating plate  
corresponds to the voltage in your home.  
Never use the appliance if it is damaged in any way.  
Before use for the first time remove any sticker or protective foil from the soleplate  
and clean the soleplate with a soft cloth.  
When you have finished ironing, and also when leaving the iron even for a short  
while:  
o Set the steam control to off position  
o Remove the power plug from the wall socket  
Take care that children cannot touch the iron while it is hot and that they cannot pull  
the power cord.  
DANGER OF BURNS! Burns can occur from touching hot metal parts, hot water or  
steam. Use caution when you turn iron upside down – there may be hot water in the  
water tank.  
Unplug from the wall socket before filling the iron with water or pouring out the  
remaining water after use.  
Do not unplug the iron by pulling on the power supply cord.  
Never immerse the iron in water.  
Some parts of the iron have been slightly greased and as a result the iron may  
slightly smoke when switched on for the first time. If this (harmless) effect does  
occur it will cease after a short while.  
Do not put vinegar or other descaling agents into water tank.  
Do not use chemically descaled water.  
The power cord should not be allowed to touch the soleplate when it is hot. Let iron  
cool completely before putting away. Loop cord loosely around iron when storing.  
Regularly check if the power cord is still in a good and safe condition.  
The ejected steam is hot and therefore hazardous. Never direct the steam towards  
people.  
This appliance is not intended for use by young children.  
The user must not leave the iron unattended while it is connected to the power  
supply.  
Young children should be supervised to ensure that they do not play with the  
appliance.  
SAVE THESE INSTRUCTIONS!  
2
 
SPECIAL INSTRUCTIONS  
To avoid a circuit overload, do not operate another high wattage appliance on the  
same circuit.  
If an extension cord is absolutely necessary a 10amp cord should be used. Cords  
rated for less amps may overheat. Care should be taken to arrange the cord so that  
it can not be pulled or tripped over.  
If the power cord is damaged, it must be replaced by the manufacturer or its service  
agent or a similarly qualified person in order to avoid a hazard.  
WARNING RISK OF BURNING: Please be aware that when the auto shut-off  
function is activated the soleplate is still extremely hot and will need adequate time  
to cool down. DO NOT TOUCH HOT SOLEPLATE!  
SAVE THESE INSTRUCTIONS  
GENERAL SAFETY INSTRUCTIONS  
WARNING! Read and understand all instructions. Failure to follow all instructions  
listed below may result in electric shock, fire or serious personal injury. The warnings,  
cautions, and instruction discussed in this instruction manual cannot cover all possible  
conditions and situations that may occur. It must be understood by the operator that  
common sense and caution are a factor which cannot be built into this product, but must  
be supplied by the operator.  
SAVE ALL INSTRUCTIONS!  
CAUTION: A short power supply cord is provided to reduce the risk of personal injury  
resulting from becoming entangled in or tripping over a longer cord. Extension cords are  
available from local hardware stores and may be used if care is exercised in their use. If  
an extension cord is required, special care and caution is necessary. Also the cord must  
be: (1) marked with an electrical rating of 125 V, and at least 13 A., 1625 W., and (2)  
the cord must be arranged so that it will not drape over the countertop or tabletop  
where it can be pulled on by children or tripped over accidentally.  
ELECTRIC POWER  
If electric circuit is overloaded with other appliances, your appliances may not operate  
properly. The appliances should be operated on a separate electrical circuit from other  
operating appliances.  
POLARIZED PLUG  
This appliance has a polarized plug (one blade is wider than the other). As a safety  
feature to reduce the risk of electrical shock, this plug is intended to fit in a polarized  
outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still  
does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.  
SAFETY WARNING  
Although your appliance is easy to operate, for your safety, the below warnings must be  
followed:  
1. Do not place the appliance near a heat source.  
2. Never leave the appliance unattended while connected to the electrical outlet.  
3. To avoid any accidental burns, never put a hand over a steam outlet when the  
appliance is in operation.  
4. Use the appliance on a stable surface away from water.  
5. Do not unplug from the socket by pulling on the power cord.  
6. The appliance must be unplugged:  
A. Before either filling or emptying  
C. After Use  
B. Before any cleaning or maintenance  
D. If it appears to be faulty  
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.  
3
 
LIST OF MAIN PARTS  
PARTS DESCRIPTION  
A. Spray nozzle  
B. Water filling inlet  
C. Variable steam control  
H. Power supply cord  
I. Swiveling cord protector  
J. Soft hand grip  
D. Steam button  
E. Spray button  
F. Power on/Auto shut-off indicator  
G. Temperature indicator light  
K. Transparent water tank  
L. Temperature control dial  
M. Soleplate  
TECHNICAL SPECIFICATIONS:  
Model Number  
Item #  
ES-139B  
1996-05  
Rating Voltage  
Rating Wattage  
Water Tank  
110-120 volt  
1200 watt  
9.15 Ounce  
CONTENTS OF PACKAGING  
a. Steam Iron  
b. Water filling beaker  
c. Instruction manual  
If any of the above items are missing, please contact our service department at 1-888-  
4
 
OPERATION  
The temperature indicator light switches on while the appliance is heating up and  
switches off as soon as the set temperature is reached. If the temperature of the hot  
iron drops, you can continue ironing while the iron heats up again to the set  
temperature.  
OPERATION AND USE  
1. Textiles with applications (gloss, crinkle, relief etc.) are best ironed at a lower  
temperature.  
2. Sort the fabric according to ironing temperature; put wool with wool, cotton with  
cotton, etc. The iron heats up more quickly than it cools down. Therefore, start  
ironing articles that need to be ironed at lowest temperature, such as those made of  
synthetic fiber.  
3. Temperature guide:  
Follow the ironing instructions on the garment label. If there are no instructions but  
you do know the kind of fabric, please consult the table.  
Warning: If the fabric consists of various kinds of fabrics, always select the  
temperature required by the most delicate fiber.  
Fabric  
Synthetic fibers nylon  
Temperature control  
Ironing methods  
Iron the reverse side. Do  
not use the spray function,  
as spraying could cause  
stains  
.
Silk wool  
Iron the reverse side to  
prevent shiny spots.  
It is recommended to set  
the dial to steam position.  
..  
Cotton linen  
Positions  
Variable Steam Control  
Normal Steam  
Maximum Steam  
Self cleaning  
Steam OFF  
5
 
How to use your Steam Iron  
When using your iron for the first time, remove any stickers or protective foil from  
soleplate. Test the iron on any piece of old fabric to ensure the soleplate and water tank  
are clean.  
Filling with water (Fig. 1)  
WARNING: Unplug the iron first!  
Choice of water  
This iron can be filled with normal tap water although it is recommended that bottled  
spring water be used. DO NOT USE DISTILLED WATER.  
1. Set the steam control to off position.  
2. Open the water filling inlet cover (Fig.1).  
3. Hold the iron at 10°, and fill in water through the water filling inlet.  
4. Use only tap water. However, if the water is very hard, it is advisable to use bottled  
spring water. Other liquids will damage the appliance. NEVER fill above the “Max”  
mark, otherwise the tank will overflow!  
5. Make sure that you have securely closed the water filling inlet cover. When ironing is  
complete please empty the water tank.  
WARNING: Never fill the iron with fabric conditioner, starch or other solutions,  
as they will damage the iron.  
Setting the temperature for the first time  
a) Fill the water tank with tap water or bottled spring water.  
b) Connect the iron to electrical power outlet.  
c) Turn the temperature dial in a clockwise direction to the MAX position. The  
temperature indicator light will illuminate.  
d) The indicator light will go off once the pre-set temperature is reached.  
e) Move the variable steam control dial to the  
come out of the holes in the soleplate.  
position and steam will start to  
f) Iron onto the old piece of fabric to test heat.  
g) When the water tank is empty and no more steam is being produced, the iron is  
ready for normal use.  
6
 
Spraying (Fig. 2)  
Spraying Water  
At any temperature by pushing on the spray button a couple of times, the laundry can  
be damped down. Ensure that there is enough water in the water tank (Fig. 2).  
Shot of steam  
By pressing steam button, an intense shot of steam is emitted from the soleplate. This  
is ideal for removing stubborn wrinkles and creases. The shot of steam feature can  
be used only while ironing with high ironing temperature. Do not overuse the  
burst of steam. Allow several seconds in between each burst (Fig. 3).  
Shot of Steam (Fig.3)  
Vertical Steam  
Press and release the surge of steam button to produce a powerful surge of vertical  
steam. This feature is ideal for steaming curtains and hanging suits.  
ƒ
Place iron in a vertical position.  
ƒ
By pressing the steam button at intervals you can also iron vertically (curtains,  
hung garments, etc).  
ƒ
ƒ
The steam function can only be used at high temperatures.  
Never vertical steam a garment put on a person, only steam when garment is on  
a hanger.  
Ironing without steam  
For ironing without steam proceed as described for steam ironing. However, the steam  
control should remain in position  
for no steam output.  
Auto Shut- off Indicator (automatic safety shut-off)  
Please note:  
ƒ
If the iron is left motionless in the horizontal position for 30 seconds the iron will  
be switched off automatically.  
7
 
ƒ
ƒ
ƒ
If the iron is left motionless in the vertical position for more than 8 minutes, the  
iron will be switched off, automatically.  
To indicate that the iron has shut off automatically, the auto shut-off indicator  
will start blinking and six sound signals will be audible.  
WARNING RISK OF BURNING: Please be aware that when the auto shut-off  
indicator is activated the soleplate is still extremely hot and will need adequate  
time to cool down. DO NOT TOUCH HOT SOLEPLATE!  
To switch the iron back on after it has automatically been shut off please note  
the following instructions:  
When picking up the iron again, the auto shut-off indicator will stop blinking.  
The temperature indicator light will illuminate indicating that the iron is heating up.  
Wait for the temperature indicator light to go off indicating that the iron has reached  
its desired temperature. Then you can resume ironing.  
MAINTENANCE  
CAUTION:  
Always be sure that the appliance is unplugged before cleaning or attempting to store  
the item.  
MAINTENANCE AND CLEANING  
WARNING: Unplug the iron first!  
ƒ
ƒ
ƒ
Allow to cool completely.  
Hold the iron at an angle and empty the water tank.  
After iron is thoroughly cooled wipe the housing and the soleplate with a damp  
cloth only. If the soleplate is very dirty, iron a linen cloth soaked in white vinegar  
then wipe with a clean damp cloth.  
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Avoid scratching the plate with steel wool.  
DO NOT immerse the iron in any liquid.  
Store the iron upright and not on the soleplate (risk of corrosion).  
Do not wind power cord tightly around iron.  
Avoid hard water with impurities that cause residue build-up.  
Regularly clean the soleplate.  
Avoid pressing iron over sharp objects like zippers and buttons.  
Do not place iron face down on rough areas.  
Empty the tank after each use and hold horizontally for a few seconds until  
remaining moisture is removed. (Use caution as steam and boiling water can  
cause burns).  
ƒ
Do not use abrasive cleaners to remove burnt-on residues.  
Self Cleaning Function  
It is important to apply “self-cleaning” at least every two weeks to remove impurities  
etc. The harder the water the more the iron should be self-cleaned.  
1. Open the water filling inlet and fill the water tank up to the MAX position, then  
close the inlet cover.  
2. Plug in steam iron into electrical wall socket.  
3. Set the temperature control to MAX.  
4. Allow the iron to heat up until the temperature indicator light goes off.  
5. Hold the iron horizontally over the sink.  
6. Turn the steam control knob to the self-clean position  
.
7. Remove the steam control knob as described in the section below “Removing the  
Variable Steam Control Knob”  
8
 
8. Boiling water and steam will now be ejected from the holes in soleplate.  
Impurities are washed away with it. Move the iron forward and backward over  
the sink during this process.  
9. When the water tank has become empty, reinsert the steam control knob and set  
the steam control to “no steam” position  
.
10.If necessary repeat self cleaning to be sure all impurities have been washed out.  
11.Move the iron over a (preferably) old piece of fabric. This is to ensure that the  
soleplate will be dry during shortage.  
12. Set the temperature control dial to “OFF”, unplug the power supply cord and  
allow the iron to cool down before storing it.  
WARNING: Take care not to scald yourself during the cleaning process.  
Removing the Variable Steam Control Knob  
The Variable Steam Control Knob will need to be removed prior to self cleaning. Review  
the following instructions to remove the Variable Steam Control Knob properly.  
Change the steam control to self-clean  
position.  
Variable Steam Control Knob will pop up.  
Grasp the Variable Steam Control Knob  
and remove.  
Variable Steam Control Knob.  
Please note notch on steam iron and 2  
tabs on the Variable Steam Control Knob.  
These will help you insert the control knob  
properly when self-cleaning is complete.  
To reinsert slide the control knob into the  
opening of the steam iron. Push the knob  
all the way down. The twist clockwise to  
engage knob.  
9
 
STORING  
Allow the appliance to cool completely before storing. Loop cord loosely around the iron  
when storing. Store the appliance in a dry location. Do not place any heavy items on  
top of appliance during storage as this may result in possible damage of appliance. Store  
the cord in a clean, dry location away from metal objects.  
NOTE: The soleplate may become damaged if the iron is stored facing downward.  
TROUBLE SHOOTING  
Problem  
Solution  
The iron emits a brown substance  
The brown substance may be caused by  
organic matter or iron minerals in the tap  
water. We recommend switching to bottled  
spring water. Once you change water it  
may take several uses before your iron  
adjusts to the new mixture and the issue is  
corrected.  
The iron is spitting and leaking  
First, check the water you use. DO NOT  
USE DISTILLED WATER. We recommend  
using tap water (up to 12 grains of  
hardness per gallon) or bottled spring  
water. If you change water, it may take  
several uses before your iron adjusts to  
the new mixture and the issue is corrected  
The white flakes can be caused by calcium  
or other minerals in the tap water. To  
solve this problem, switch to bottled spring  
water. Once the water is changed it may  
take several uses before your iron adjusts  
to the new mixture and the issue is  
corrected.  
The iron emits white flakes  
Build-up on the soleplate  
During normal use, a sticky film caused by  
starch and melted fibers can build up on  
the soleplate. Iron a linen cloth soaked  
with white vinegar.  
10  
 
SERVICE CENTER  
If you have any question in regards to the operation of this appliance or are in need of a  
spare part please contact our service center at:  
Wachsmuth & Krogmann, Inc.  
Tel: 1-888-367-7373  
(Business hours Mon-Fri 9:00am - 4:00pm CT)  
ENVIRONMENTAL PROTECTION  
If the appliance should no longer work at all, please make sure that it is disposed in an  
environmentally friendly way, by handing it into a public collection point. Please do not  
put it with your household waste.  
11  
 
LIMITED WARRANTY  
Thank you for purchasing a top quality Crofton product. This Steam Iron item  
#1996-05 was tested and meets our stringent quality standards. This product is  
warranted to be free from manufacturing defects in original materials, including  
original parts, and workmanship until August 22, 2007 or 2 year with proof of  
purchase.  
The warranty is void if the defect is due to accidental damage, misuse, abuse,  
neglect, improper repair or alteration by unauthorized persons or failure to follow  
operation instructions provided with the product. This warranty does not apply to  
commercial use.  
The warranty is non-transferable and applies only to the original purchase and  
does not extend to subsequent owners of the product. Liability under this  
warranty is limited to repair, replacement or refund. In no event shall liability  
exceed the purchase price paid by the purchaser of the product. Under no  
circumstances shall there be liability for any loss, direct, indirect, incidental,  
special or consequential damage arising out of in connection with use of this  
product. This warranty is valid only in the United States of America. This Warranty  
gives you specific legal rights. However you may have other rights that vary from  
state to state. Some states do not allow limitation on implied warranties or  
exclusion of consequential damages therefore these restrictions may not apply to  
you.  
In case you find the product to be defective please send it within the warranty  
period to our service center. To avoid transport damages please send the product  
in the original packaging. In return you will either receive your repaired item, a  
new product or a refund. Please fill out the Warranty Card and send it together  
with the product and purchase receipt  
To arrange pick-up of the defective item please call our service center:  
Wachsmuth & Krogmann Inc.  
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)  
1800 Nicholas Blvd,  
Elk Grove, IL 60007,  
USA  
12  
 
WARRANTY CARD  
Crofton Steam Iron, Item # 1996-05, Model # ES-139B  
In case you find this product to be defective please send it within the  
warranty period to our service center. To avoid transport damages please  
send the product in the original packaging. In return you will receive your  
repaired item, a new product or a refund.  
This Crofton Steam Iron was tested and meets our stringent quality  
standards. This product is warranted to be free from manufacturing  
defects in original materials, including original parts, and workmanship  
until August 22, 2007 or 2 year with proof of purchase.  
Please fill in your details below and send it together with the product and  
purchase receipt. Please read the Limited Warranty conditions mentioned  
in this instruction manual.  
Customer Name  
Street  
City  
State  
ZIP Code  
Purchase Date  
Description of Defect :  
To arrange pick-up of the defective item please call our service center:  
Wachsmuth & Krogmann Inc.  
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)  
1800 Nicholas Blvd,  
Elk Grove, IL 60007,  
USA  
13  
 

Tatung Home Theater Screen TBM 0903 User Manual
Taylor Wheelchair C810 User Manual
Toshiba Cash Register Electronic Cash Register User Manual
Toshiba Digital Camera IK 645A User Manual
TRENDnet Network Router BRF114 User Manual
ViewSonic Car Video System VX2235wm User Manual
Viking Burner 48 W User Manual
Vizio Flat Panel Television M75 C1 User Manual
VTech Cordless Telephone VT 1711 User Manual
Walgreens Cable Box XVT423SV User Manual